Pool Thermometer nutzen
Ich nutze ein 433 mhz Poolthermometer… Dies möchte ich mit Pimatic steuern. Leider kennt Pimatic das Protokoll nicht, und findet demnach kein Device . Wie kann ich hier vorgehen ?
Pool Thermometer
Pool Thermometer nutzen
Ich nutze ein 433 mhz Poolthermometer… Dies möchte ich mit Pimatic steuern. Leider kennt Pimatic das Protokoll nicht, und findet demnach kein Device . Wie kann ich hier vorgehen ?
Welches Pool Thermometer und womit empfängst du (Homeduino, RFlink, RFXtrx433,…)?
hmm, denn kenne ich nicht.
nutze selber auch kein homeduino mehr, zumindest aktuell. habe bessere erfahrung
mit rflink gemacht. in meinem pool habe ich einen TFA Dostmann 30.3177, der läuft
soweit. allerdings mit kabel, der sensor klemmt unter dem skimmer
Die devs benötigen genaue temp Daten und das debug protocol zum entwickeln
Wir suchen Unterstützung im Bereich homeduino und Plugin Support zur weiteren Entwicklung von pimatic
pimatic v0.9 has been released!
Support Pimatic and get some free stickers
Like us on Facebook
make it so !
@leader Wie komme ich an solche Daten?
Du musst in der config das debuggen aktivieren und dann kannst du in Pimatic links oben das Menue öffnen und unter Log auf Messages klicken.
Dann oben Links im Dropdown-Menue Info, Warn und Error abwählen und nur Debug auswählen.
In Dropdown-Menue daneben noch Homeduino anwählen und es werden alle Daten welche Homeduino auf 433Mhz empfängt angezeigt.
Sind meistens einige…
@strato345 said in Pool Thermometer:
Ich habe ein homeduino Empfänger
I have had 2 of these make/model. They will brake very soon because the floating part is not completely watertight.
Like my projects and help? Consider donating electroneum etnjwAKGPqF6omQWRmpp9u2BPyVDG9VuyRQjNJ1S8yfBdfR9qeUQ46kRy8KS2CNqbpNLRrsgmNW6F2TMzxmZgPrh6KctrkrYbm
Funktionieren die mit homeduino?
@V1per wie aktiviere ich den debug Mode in der config
Total different approach : mount a DS18B20 in your pool plumbing - i have connected 2 to my setup one in the main and on the return.
Like my projects and help? Consider donating electroneum etnjwAKGPqF6omQWRmpp9u2BPyVDG9VuyRQjNJ1S8yfBdfR9qeUQ46kRy8KS2CNqbpNLRrsgmNW6F2TMzxmZgPrh6KctrkrYbm
Debug Mode sollte theoretisch aktiviert sein. Ansonsten Mal hier schauen https://forum.pimatic.org/topic/202/4-homeduino-433-mhz-sending-receiving-and-even-more/3
pimatic v0.9 has been released!
Support Pimatic and get some free stickers
Like us on Facebook
make it so !
Also bei mir wird bei debug nichts angezeigt Hab alles so eingestellt wie es im post beschrieben ist
Dann tippe ich mal auf einen Verkabelungs oder Hardwarefehler, hast du dir den Beitrag den leader21 oben verlinkt hat angesehen und noch mal alles überprüft?
Ja ich benutze Elro Steckdosen die funktionieren einwandfrei auch die Fernbedienung wird eingelesen
Also nochmals zusammenfassend. Die FB der elro Dosen wird im Debug gelesen. Auch ein anderer Temperaturfühler einer alten Wetterstation wird eingelesen. Mit diesem erfasse ich die Raumtemperatur im Wohnzimmer. Nur das Pooltermometer wird nicht angezeigt.
@strato345 so you are not getting any debug data from the thermometer but other devices return a signal. This can be because the signal isnt good. Could you try closer to the receiver? Also, not sure though, if pimatic does nog recognize the protocol you should get “unknown” and soms data.
So bekommst du keine Debug-Daten aus dem Thermometer, aber andere Geräte geben ein Signal zurück. Das kann sein, weil das Signal nicht gut ist. Könnten Sie dem Empfänger näher kommen? Auch nicht sicher aber wenn pimatic nog das Protokoll erkennt man “unbekannt” und soms Daten.
The thermometer is 10cm away from the receiver. There is no data. I do not understand why? With another thermometer works the debug
Maybe the thermometer works on 833MHz?
In the manual its 433Mhz