Howto do a Raspee (Conbee II) installation?

quotschmacher

i had to send my conbee II back, too and the new one shall be there till friday. couldn’t connect to it anymore, even after firmware update and setting up the pi completely from scratch. but that gave me some time to get to know the deconz docker image - so the setup step isn’t required anymore.

Pedder

Hmhm, I hope that they do not break too often …

Pedder

Hi again

I was happy that now, against the former announcements, my new ConBee II stick has been delivered yesterday.
Today I directly took a fresh Test Image an started the installation.
Everything went very well, using @kosta’s install guide from github

But after doing a rebooted I ran into the problem, that deconz seems not to be started automatically and so pimatic comes up with a websocket reconnection error.

I found, that I have always to start the deconz service manually by:
sudo systemctl start deconz
what for sure is not needful, e. g. in terms of a power outage…

So my question today: How can I get deconz also beeing started automatically after a reboot?
Is that similiar like I did already for autostarting pimatic, as it is explained in the wiki?

wget https://raw.githubusercontent.com/pimatic/pimatic/v0.9.x/install/pimatic-init-d
sudo cp pimatic-init-d /etc/init.d/pimatic
sudo chmod +x /etc/init.d/pimatic
sudo chown root:root /etc/init.d/pimatic
sudo update-rc.d pimatic defaults

… or maybe as another solution, as I have installed the shell execute plugin, to execute the above mentioned command only once after a pimatic start - currently have no clue how to do that, as I fear, that it would be executed again and again …

Pedder

@pedder said in Howto do a Raspee (Conbee II) installation?:

installed the shell execute plugin, to execute the above mentioned command only once after a pimatic start -

Ok, that works for the moment:
WHEN ‘pimatic is starting’ THEN ‘after 5 seconds execute “sudo systemctl start deconz”’
It creats 1-2 errors in the starting phases, but it works

Other solutions are welcome in addition

kosta

@Pedder
deconz already has a startup script so you can control the service via systemctl
you can check if the autostart is enabled

sudo systemctl is-enabled deconz

# if disabled 
sudo systemctl enable deconz

Pedder

Hi @kosta,
thanks for the additional hint.

Freshly back from vacations, I will check that the next days …

scobby

Best way to install deconz is:

https://hub.docker.com/r/marthoc/deconz

Here is my current docker-compose.yml:

version: "2"

services:

  deconz:
    image: marthoc/deconz
    container_name: deconz
    network_mode: host
    ports:
      - "8090:8090"
      - "8443:8443"
    restart: always
    command: --upnp 0
    volumes:
      - ./localconfig:/root/.local/share/dresden-elektronik/deCONZ
      - /dev/ttyUSB0:/dev/ttyAMA0
    devices:
      - /dev/deconz
      - /dev/ttyUSB1
      - /dev/ttyUSB0

    environment:
      - DECONZ_WEB_PORT=8090
      - DECONZ_WS_PORT=8443
      - DEBUG_INFO=1
      - DECONZ_DEVICE=/dev/deconz
      - DEBUG_APS=0
      - DEBUG_ZCL=0
      - DEBUG_ZDP=0
      - DEBUG_OTAU=0
      - DECONZ_UPNP=0

The Deconz Device is hard-linkt via udev rule in /etc/udev/rules.d/10-local.rules

ACTION=="add", ATTRS{idVendor}=="0403", ATTRS{idProduct}=="6015", SYMLINK+="deconz"

Hope you have fun with this!