MySensors ID ?!
Hello,
I have built several sensors. These are also shown to me in the debug.
But I have problems to build from the sensors devices.
I have this log:
<- I_LOG_MESSAGE 0; 255; 3; 0; 9; TSP: MSG: READ 2-2-0 s = 3, c = 1, t = 16, pt = 2, l = 2, sg = 0: 1
<- I_LOG_MESSAGE 0, 255, 3, 0, 9, TSP: MSG: READ 2-2-0 s = 3, c = 1, t = 16, pt = 2, l = 2, sg = 0: 0
How is the construction or how can I see what nodeid, sensorid, sensortype???
Thanks
I have it
{
"id": "MySensors_Contact",
"name": "Test",
"class": "MySensorsButton",
"nodeid": 2,
"sensorid": 3,
"batterySensor": true
},You can also use device Discovery. Should find it when it powers Up.
First in German:
Guten Abend sitze mal wieder an meinen mysenors, verwende einen DHT22 im Arduino Monitor bekomm ich den angehangenen Output.
Mein Problem Pimtaic gibt mir keine Werte raus habe zweo Devices, das erste selber erstellt mit MySensorsDHT und das zweite über die Discover funktion dort wurde der Sensor als DST erkannt.
Die ID welche ich eintragen müsste wäre 4.1
Kann mir jemand sagen wo der Fehler liegt bzw wie ich das ganze zum laufen bekomme?
Good evening,
My DHT Mysensor Device does not show me any values in pimatic.
I have it manually entered into the config as mysensorsdht and have it over the Disvocer function where it was recognized as dst.
Both show no values.
ID should be 4.1
ü0 MCO:BGN:INIT NODE,CP=RNNNA--,VER=2.1.1 40 TSM:INIT 55 TSF:WUR:MS=0 77 TSM:INIT:TSP OK 96 TSF:SID:OK,ID=4 116 TSM:FPAR 165 TSF:MSG:SEND,4-4-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK: 573 TSF:MSG:READ,0-0-4,s=255,c=3,t=8,pt=1,l=1,sg=0:0 628 TSF:MSG:FPAR OK,ID=0,D=1 2238 TSM:FPAR:OK 2254 TSM:ID 2269 TSM:ID:OK 2283 TSM:UPL 2301 TSF:MSG:SEND,4-4-0-0,s=255,c=3,t=24,pt=1,l=1,sg=0,ft=0,st=OK:1 4374 TSM:UPL 4388 TSF:MSG:SEND,4-4-0-0,s=255,c=3,t=24,pt=1,l=1,sg=0,ft=0,st=OK:1 6461 TSM:UPL 6475 TSF:MSG:SEND,4-4-0-0,s=255,c=3,t=24,pt=1,l=1,sg=0,ft=0,st=OK:1 6615 TSF:MSG:READ,0-0-4,s=255,c=3,t=25,pt=1,l=1,sg=0:1 6674 TSF:MSG:PONG RECV,HP=1 6703 TSM:UPL:OK 6719 TSM:READY:ID=4,PAR=0,DIS=1 6760 TSF:MSG:SEND,4-4-0-0,s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=OK:0100 6834 TSF:MSG:READ,0-0-4,s=255,c=3,t=15,pt=6,l=2,sg=0:0100 6903 TSF:MSG:SEND,4-4-0-0,s=255,c=0,t=17,pt=0,l=5,sg=0,ft=0,st=OK:2.1.1 6981 TSF:MSG:SEND,4-4-0-0,s=255,c=3,t=6,pt=1,l=1,sg=0,ft=0,st=OK:0 9056 TSF:MSG:SEND,4-4-0-0,s=255,c=3,t=11,pt=0,l=22,sg=0,ft=0,st=OK:TemperatureAndHumidity 9154 TSF:MSG:SEND,4-4-0-0,s=255,c=3,t=12,pt=0,l=3,sg=0,ft=0,st=OK:1.1 9230 TSF:MSG:SEND,4-4-0-0,s=0,c=0,t=7,pt=0,l=0,sg=0,ft=0,st=OK: 9297 TSF:MSG:SEND,4-4-0-0,s=1,c=0,t=6,pt=0,l=0,sg=0,ft=0,st=OK: 9365 MCO:REG:REQ 9385 TSF:MSG:SEND,4-4-0-0,s=255,c=3,t=26,pt=1,l=1,sg=0,ft=0,st=OK:2 11456 TSF:MSG:SEND,4-4-0-0,s=255,c=3,t=26,pt=1,l=1,sg=0,ft=0,st=OK:2 11530 TSF:MSG:READ,0-0-4,s=255,c=3,t=27,pt=1,l=1,sg=0:1 11587 MCO:PIM:NODE REG=1 11614 MCO:BGN:STP 11638 MCO:SLP:MS=2000,SMS=0,I1=255,M1=255,I2=255,M2=255 11698 MCO:SLP:TPD 11716 MCO:SLP:WUP=-1 11739 MCO:BGN:INIT OK,TSP=1 11776 TSF:MSG:SEND,4-4-0-0,s=1,c=1,t=0,pt=7,l=5,sg=0,ft=0,st=OK:24.0 T: 24.00 11853 TSF:MSG:SEND,4-4-0-0,s=0,c=1,t=1,pt=7,l=5,sg=0,ft=0,st=OK:57.3 H: 57.30 11931 MCO:SLP:MS=60000,SMS=0,I1=255,M1=255,I2=255,M2=255 12001 MCO:SLP:TPD
My Debug in Pimatic
debug [pimatic-mysensors]: <- I_LOG_MESSAGE 0;255;3;0;9;TSP:MSG:SEND 0-0-4-4 s=255,c=3,t=27,pt=1,l=1,sg=0,ft=0,st=ok:1 18:26:59debug [pimatic-mysensors]: <- I_LOG_MESSAGE 0;255;3;0;9;TSP:MSG:READ 4-4-0 s=255,c=3,t=26,pt=1,l=1,sg=0:2 18:26:59debug [pimatic-mysensors]: <- Presented Node [ '4', '1', '0', '0', '6', '' ] 18:26:59debug [pimatic-mysensors]: <- I_LOG_MESSAGE 0;255;3;0;9;TSP:MSG:READ 4-4-0 s=1,c=0,t=6,pt=0,l=0,sg=0: 18:26:59debug [pimatic-mysensors]: <- Presented Node [ '4', '0', '0', '0', '7', '' ] 18:26:59debug [pimatic-mysensors]: <- I_LOG_MESSAGE 0;255;3;0;9;TSP:MSG:READ 4-4-0 s=0,c=0,t=7,pt=0,l=0,sg=0: 18:26:59debug [pimatic-mysensors]: <- I_SKETCH_VERSION 4;255;3;0;12;1.1 18:26:59debug [pimatic-mysensors]: <- I_LOG_MESSAGE 0;255;3;0;9;TSP:MSG:READ 4-4-0 s=255,c=3,t=12,pt=0,l=3,sg=0:1.1 18:26:59debug [pimatic-mysensors]: <- I_SKETCH_NAME 4;255;3;0;11;TemperatureAndHumidity 18:26:59debug [pimatic-mysensors]: <- I_LOG_MESSAGE 0;255;3;0;9;TSP:MSG:READ 4-4-0 s=255,c=3,t=11,pt=0,l=22,sg=0:TemperatureAndHumidity 18:26:59debug [pimatic-mysensors]: <- I_LOG_MESSAGE 0;255;3;0;9;TSP:MSG:SEND 0-0-4-4 s=255,c=3,t=6,pt=0,l=1,sg=0,ft=0,st=ok:M 18:26:58debug [pimatic-mysensors]: -> Sending 4;255;3;0;6;M 18:26:58debug [pimatic-mysensors]: <- I_CONFIG 4;255;3;0;6;0 18:26:58debug [pimatic-mysensors]: <- I_LOG_MESSAGE 0;255;3;0;9;TSP:MSG:READ 4-4-0 s=255,c=3,t=6,pt=1,l=1,sg=0:0 18:26:58debug [pimatic-mysensors]: <- Presented Node [ '4', '255', '0', '0', '17', '2.1.1' ] 18:26:58debug [pimatic-mysensors]: <- I_LOG_MESSAGE 0;255;3;0;9;TSP:MSG:READ 4-4-0 s=255,c=0,t=17,pt=0,l=5,sg=0:2.1.1 18:26:58debug [pimatic-mysensors]: <- I_LOG_MESSAGE 0;255;3;0;9;TSP:MSG:SEND 0-0-4-4 s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=ok:0100 18:26:58debug [pimatic-mysensors]: <- I_LOG_MESSAGE 0;255;3;0;9;TSP:MSG:READ 4-4-0 s=255,c=3,t=15,pt=6,l=2,sg=0:0100 18:26:58debug [pimatic-mysensors]: <- I_LOG_MESSAGE 0;255;3;0;9;TSP:MSG:SEND 0-0-4-4 s=255,c=3,t=25,pt=1,l=1,sg=0,ft=0,st=ok:1 18:26:58debug [pimatic-mysensors]: <- I_LOG_MESSAGE 0;255;3;0;9;TSP:MSG:PINGED (ID=4, hops=1) 18:26:58debug [pimatic-mysensors]: <- I_LOG_MESSAGE 0;255;3;0;9;TSP:MSG:READ 4-4-0 s=255,c=3,t=24,pt=1,l=1,sg=0:1 18:26:57debug [pimatic-mysensors]: <- I_LOG_MESSAGE 0;255;3;0;9;TSP:MSG:SEND 0-0-4-4 s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=ok:0 18:26:56debug [pimatic-mysensors]: <- I_LOG_MESSAGE 0;255;3;0;9;TSP:MSG:GWL OK 18:26:56debug [pimatic-mysensors]: <- I_LOG_MESSAGE 0;255;3;0;9;TSP:CHKUPL:OK 18:26:56debug [pimatic-mysensors]: <- I_LOG_MESSAGE 0;255;3;0;9;TSP:MSG:FPAR REQ (sender=4) 18:26:56debug [pimatic-mysensors]: <- I_LOG_MESSAGE 0;255;3;0;9;TSP:MSG:BC 18:26:56debug [pimatic-mysensors]: <- I_LOG_MESSAGE 0;255;3;0;9;TSP:MSG:READ 4-4-255 s=255,c=3,t=7,pt=0,l=0,sg=0: 17:14:48info [pimatic-mysensors]: Connected to MySensors Gateway.
Please post your plugin settings and you device settings.
Sry for the late answer
MyPimaticCFG:
{
"nodeid": 4,
"sensorid": [
255,
3,
0,
6,
0
],
"batterySensor": true,
"xAttributeOptions": [],
"id": "kammerchen2",
"name": "Kämmerchen2",
"class": "MySensorsDHT"
},
`
{
"plugin": "mysensors",
"driver": "serialport",
"protocols": "2.0.0",
"startingNodeId": 4,
"driverOptions": {
"//": "'/dev/ttyUSB1' if using serial Gateway",
"serialDevice": "/dev/ttyUSB1",
"baudrate": "9600"
},
"debug": true,
"active": true
}
My Plant are ok with this cfg
{
"class": "MySensorsMulti",
"id": "Soil_Gummibaum",
"name": "Erdfeuchte Lemone",
"attributes": [
{
"name": "Erdfeuchte Orchideen",
"nodeid": 3,
"sensorid": 1,
"type": "integer",
"unit": "%",
"sensortype": 37,
"booleanlabels": [
null,
null
]
},
{
"name": "Battery",
"nodeid": 3,
"type": "battery",
"unit": "%",
"booleanlabels": [
null,
null
],
"sensortype": 37
}
],
"xAttributeOptions": []
},
What is wrong with the DHT?!
Missing DHT Device?
There is a Sensor TemperatureAndHumidity please use this.
Please add this config here. Please formate your settings for this form well.
is a MySensorsDHT Device… the id is wrong i know it is for testing -> try and error
I use a DHT22 on the Homeduino with this, but is no MySensors
@wuschel said in MySensors ID ?!:
What is wrong with the DHT?!
Please take into to account that DHT sensor might be broken as we had some cases in the past. Make sure you have some spare sensor you can test with.
"It always takes longer than you expect, even when you take into account Hofstadter's Law.", Hofstadter's Law
Thats it… I use the DHT22 from my test Breadboard and it works…
Sensor ID 255? Is that really needed? I use only 0 and 1 and it is working.
@Swen said in MySensors ID ?!:
Sensor ID 255? Is that really needed? I use only 0 and 1 and it is working.
is not needed, i use 0 and 1
But you setting has input 255.
That was testing -> Try and Error
OK, please post code what are you really using or we look for bad thinks they are not there.
Which sketch are you using? MySensor DHT?
yes i use this sketch
https://www.mysensors.org/build/debug
Check NodeId… I think its not 4 its 255…
