Romotec TT2ND

---

Hey,

i have bought a romotec blinds device. I hoped that i can use ist without buy an extra Remote…
Now, i have just copy and paste the device config from @Thrusty , but the switch issnt working.

I Dont know, how can i get the device in the “learn” mode. I just become 2 beeps - thats all.

This is the device:
https://forum.pimatic.org/topic/35/supported-devices-plug-and-play/20

has anyone an idea?

Ok,

i have found something:

Now i need a solution, to emulate the Programmbutton with Pimatic. Can anyone with a remote send me the data of the programm button? Than can i emulate the Programmbutton.

Thank You!

EDIT: the whole instruction manual
http://www.rohrmotor24.eu/mediafiles//Sonstiges/R24-RMF-R1-UP-Funkempfaenger-2012-06.pdf

@schmucke said in Romotec TT2ND:

Ok,

i have found something:

Now i need a solution, to emulate the Programmbutton with Pimatic. Can anyone with a remote send me the data of the programm button? Than can i emulate the Programmbutton.

Thank You!

EDIT: the whole instruction manual
http://www.rohrmotor24.eu/mediafiles//Sonstiges/R24-RMF-R1-UP-Funkempfaenger-2012-06.pdf

My German is rubbish but doesnt it say that if you turn your power on, it goes into learning mode?

Create the device and it should display a on/off or up/down button that you have to press when it is in learning mode.

Otherwise, ask the question in that topic.

@schmucke maybe you can ask @GuybrushMR80 ih he can sent his debug output.
He has the same switch and a remote: https://forum.pimatic.org/topic/2164/solved-skylights-setup

thank you!

the problem is, the most users comming to solve a problem… i hope there joining the forum in the next days…

if not, i must buy me a remote.

Hi,

this is the debug output when I push the program button twice

21:41:14debug [pimatic-homeduino]: shutter3:  { id: 302736933, channel: 1, command: undefined }
21:41:14debug [pimatic-homeduino]: received: [ 356, 720, 1524, 4692, 8672 ] 3210010110010101010110011010011010010110100101011001011001100101101010010110100104
21:41:14debug [pimatic-homeduino]: data: "RF receive 4692 1524 720 356 8672 0 0 0 0123323223323232323223322323322323323223233232322332322332233232232323323223233234"

Ah thank you!!!

one step more in this challenge.

i think, there is a “config” command or what ever?!

@Willy ? Can you encrypt this?

sorry to tell but willy hasn’t been on for over a year now
have a look at this example here , maybe it helps to set up your device
https://forum.pimatic.org/topic/2164/solved-skylights-setup/11

Wasn´t there a possibility to sent raw code via homeduino?

https://forum.pimatic.org/topic/2203/need-protocol-for-program-button/2

@mwittig has add the programm button to shutter3

i test it today and give you a response.

there is the P2 button on the back of the remote - if I read out the debug information for this button, the result is this:

debug [pimatic-homeduino]: shutter3: { id: 390475088, channel: 1, command: undefined }
13:25:51debug [pimatic-homeduino]: received: [ 360, 720, 1496, 4808, 10424 ] 3210011010100110010101101001010110011010011001100110010101010101101010010110100104
13:25:51debug [pimatic-homeduino]: data: “RF receive 4808 1496 720 360 10424 0 0 0 0123322323233223323232232332323223322323322332233223323232323232232323323223233234”

I was hoping to see something like “sync” or “pair” and not “undefined” - but you should try it, maybe it works.

@GuybrushMR80 said in Romotec TT2ND:

I was hoping to see something like “sync” or “pair” and not “undefined” - but you should try it, maybe it works.

That’s covered by the code change I have done today. The command shown is “program” in this case.