Note: This text has been automatically translated from German into English!
Hi, community
this is my first post in the forum. Thank you for developing pimatic.
Pimatic is stable for several weeks on my Raspi. There were in the
Past priority only switches driven.
Have now been upgraded with dimmer, fitting dimmer, temperature
Outdoor sensor. These hardware works perfectly.
Problems of PIR Sensor AWST-6000 does.
This PIR comes at the rear with 4 sliders (A - D):
A) Distance - 1m 3m 6m
Switch-off if no more movement is detected,
the transmitter sends automatically after 5s, 1min, 5 min or 10 min
an OFF signal
C) LEARN with DEL / SET setting
D) light sensitivity with Always Active, below 20 lux and 10 lux
PIR reacts only sporadically on movement at a max. Distance of 3m
(far too little for a practical application):
sometimes he reacted immediately, even repeatedly, max. 4x
-> Regardless of the
setting B (see above), ie no matter what turn-on delay is active,
if he reacts times, then always immediately.
then again after 20 minutes,
-> If when setting C (see above) from SET to DEL or / and was vice versa, as well as sporadic
Conclusion: PIR broken? or to which screw should turn?
Does somebody has any idea ? Perhaps other settings in Config, protocol, parameters?
Special feature:
I position the PIR beside a switch (1m, with absent), the switch (15 m from Raspi)
can no longer switch. I remove the PIR, everything is fine.
I position the PIR near the Raspi (0.50 to 1.5 m when absent), no signals coming from
the two temperature sensors Outdoor (8 meters from Raspi) longer. Even with this small distance
the PIR reacts only sporadically.
P.S.
The above-mentioned Setting Switch-off (OFF signal) is evaluated by this pimatic?
Listed he is in> Supported devices (plug and play) <with
KAKU / COCO - AWST-6000 - PIR 5 - Movement sensor - disable reset timer: “auto reset”: false
PIR sensor Example of> for using various devices and 433mhz sensors.html <
{
“id”: “homeduino-pir”
“name”: “PIR”
“class”: “HomeduinoRFPir”
“Protocols”: [{
“name”: "PIR1"
“options”: {
“Unit”: 0,
“id”: 17
}
}],
“Reset Time”: 6000
}
Log messages:
debug [pimatic-homeduino]: contact1: {id: 19,001,062, all: false, contact: false, Unit: 9}
13: 30: 59debug [pimatic-homeduino]: pir5: {id: 19,001,062, all: false, Presence: true, Unit: 9}
13: 30: 59debug [pimatic-homeduino]: switch1: {id: 19,001,062, all: false, state: true, Unit: 9}
13: 30: 59debug [pimatic-homeduino]: Received: [144, 276, 344, 1236, 2560, 10100] 141113131211131113131111131113111311131311131113111311211313111312131202131311131113121113111313121312111311131312131111131113131115
debug [pimatic-homeduino]: data: "RF receive 276 2560 1236 344 144 10100 0 0 010002020300020002020000020002000200020200020002000200300202000203020343020200020002030002000202030203000200020203020000020002020005"
debug [pimatic-homeduino]: Sending Protocol: switch2 House code: 17 Unit Code: 3 State: true all: false Pin: Repeats 1: 7
13: 30: 59debug [pimatic-homeduino]: contact1: {id: 19,001,062, all: false, contact: false, Unit: 9}
13: 30: 59debug [pimatic-homeduino]: pir5: {id: 19,001,062, all: false, Presence: true, Unit: 9}
13: 30: 59debug [pimatic-homeduino]: switch1: {id: 19,001,062, all: false, state: true, Unit: 9}
13: 30: 59debug [pimatic-homeduino]: Received: [280, 348, 1236, 2552, 10068] 030002020000020002020000020002000200020200020002000201000202000201020000020200020002000002000202010201000200020200020000020002020004
13: 30: 59debug [pimatic-homeduino]: data: “RF receive 280 2552 1236 348 10068 0 0 0 010002020000020002020000020002000200020200020002000203000202000203020000020200020002000002000202030203000200020200020000020002020004”
My config entry looks so like this:
{
“id”: “pir”
“name”: “PIR”
“class”: “HomeduinoRFPir”
“Protocols”: [
{
"name": "pir5"
"options": {
"Unit": 9,
"id": 19001062
}
}
]
},
Device is part of the WebGUI.
I have a Rule generates so in the GUI and the outside world which can be seen:
{
“id”: “test”
“name”: “test”
“rule”: “if PIR signal present then switch light on”
“Active”: true,
“Logging”: true
},
Note: This text has been automatically translated from German into English!
