KAKU Pir in pimatic

---

Hello ,

I have a AWST-6000 KAKU pir and i want to use it as motionsensor.
Only i have a problem. I used it as pir 5 and it works. In the config.js there is resettime but it dont work because the AWST-6000 reset it every time.
I can change the time on the AWST in 5s 1m 5m 10m but i want to reset the pir when i want it to change the reset time in the config.
Is this possible?

“class”: “HomeduinoRFPir”,
“protocols”: [
{
“name”: “pir5”,
“options”: {
“unit”: 9,
“id”: 16846042
},
“receive”: true
}
],
“resetTime”: 120000

THANKS gerrit

try this:

"class": "HomeduinoRFPir",
"protocols": [
{
"name": "pir5",
"options": {
"unit": 9,
"id": 16846042
},
"receive": true
}
],
"autoReset": false

Thanks, Sweebee

I have try it but where can i put the resettime. I would like to receive when the PIR is true or high and that i can reset the PIR with a resetTime in the config. Now will reset the PIR by the debug of the AWST.

MOTION

debug [pimatic-homeduino]: contact1: { id: 16846042, all: false, contact: false, unit: 9 }
12:53:50debug [pimatic-homeduino]: pir5: { id: 16846042, all: false, presence: true, unit: 9 }
12:53:50debug [pimatic-homeduino]: switch1: { id: 16846042, all: false, state: true, unit: 9 }
12:53:50debug [pimatic-homeduino]: received: [ 264, 1080, 2564, 9452 ] 020001010000010001000100010001000100010100000100010001000101000100000100010100010000010100010000010100000100010100010000010001010003
12:53:50debug [pimatic-homeduino]: data: "RF receive 264 2564 1080 9452 0 0 0 0 010002020000020002000200020002000200020200000200020002000202000200000200020200020000020200020000

DEBUG SENDING FROM AWST-6000 after 5 seconds

debug [pimatic-homeduino]: contact1: { id: 16846042, all: false, contact: true, unit: 9 }
12:58:28debug [pimatic-homeduino]: pir5: { id: 16846042, all: false, presence: false, unit: 9 }
12:58:28debug [pimatic-homeduino]: switch1: { id: 16846042, all: false, state: false, unit: 9 }
12:58:28debug [pimatic-homeduino]: received: [ 268, 1084, 2552, 9532 ] 020001010000010001000100010001000100010100000100010001000101000100000100010100010000010100010000010100000100010001010000010001010003
12:58:28debug [pimatic-homeduino]: data: "RF receive 268 2552 1084 9532 0 0 0 0 010002020000020002000200020002000200020200000200020002000202000200000200020200020000020200020000

I would like to reset the pir after 1/2 hour but on the AWST is is the max 10 minutes.

THANKS gerrit

Hi Gerrit, I know it is quit an old post and I’m not sure if you fixed it, but you can extend the time the pir is active by using a rule. I f.i. have set the pir hardware on 5s and on H sensitivity and use rules to control the pir’s actions. F.i. turn of lights after 15 minutes and only when its is dark (between sunset and sunrise). Maybe this helps with your problem. Or someone else for that matter
Regards, Eric