Hello all,
i was running pimatic and the RXB6 Receiver/Sender directly on the GPIOs of the raspberry and everything worked wonderful (except the 40% CPU issue).
So i switched to the arduino nano clone way.
Now each day, when i try to switch on a device it sends the signal and the remote plug turns on.
but the indicator on the webinterface still is in “switching mode” (lightly grey- not on and not off). After a few seconds the “Ooops timeout” popup is comming up.
in the pimatic log is nothin to find ,
dmesg says the following:[ 3.067460] usb 1-1.1: new high-speed USB device number 3 using dwc_otg
[ 3.177781] usb 1-1.1: New USB device found, idVendor=0424, idProduct=ec00
[ 3.190749] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 3.209940] smsc95xx v1.0.4
[ 3.273904] smsc95xx 1-1.1:1.0 eth0: register ‘smsc95xx’ at usb-bcm2708_usb-1.1, smsc95xx $
[ 3.397608] usb 1-1.2: new full-speed USB device number 4 using dwc_otg
[ 3.531097] usb 1-1.2: New USB device found, idVendor=1a86, idProduct=7523
[ 3.548979] usb 1-1.2: New USB device strings: Mfr=0, Product=2, SerialNumber=0
[ 3.562024] usb 1-1.2: Product: USB2.0-Serial
[ 3.667512] usb 1-1.3: new high-speed USB device number 5 using dwc_otg
[ 3.799530] usb 1-1.3: New USB device found, idVendor=7392, idProduct=7811
[ 3.826902] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3.844215] usb 1-1.3: Product: 802.11n WLAN Adapter
[ 3.867298] usb 1-1.3: Manufacturer: Realtek
[ 3.873819] usb 1-1.3: SerialNumber: 00e04c000001
[ 4.348207] udevd[159]: starting version 175
[ 5.849078] usbcore: registered new interface driver usbserial
[ 5.968437] usbcore: registered new interface driver usbserial_generic
[ 6.056365] usbserial: USB Serial support registered for generic
[ 6.312757] usbcore: registered new interface driver ch341
[ 6.527613] usbserial: USB Serial support registered for ch341-uart
[ 6.536177] ch341 1-1.2:1.0: ch341-uart converter detected
[ 7.030698] usb 1-1.2: ch341-uart converter now attached to ttyUSB0
[ 7.737111] random: nonblocking pool is initialized
[ 8.402075] usbcore: registered new interface driver rtl8192cu
[ 11.373704] EXT4-fs (mmcblk0p6): re-mounted. Opts: (null)
[ 11.823700] EXT4-fs (mmcblk0p6): re-mounted. Opts: (null)
[ 21.822767] smsc95xx 1-1.1:1.0 eth0: hardware isn’t capable of remote wakeup
the arduino is via USB direct connected (without any usbhub)
if i restart the system or the pimatic servic, it works for about 1 or 2 hours.
Can anyone help me her?
thanks