How does a RaspBeeMultiSensor Device Config look like?

ArrowX

Hi,
for some reason my Pimatic installation cannot find the Zigbee devices connected to my ConBee II via the “Discover Devices” comand. The Phoscon-Gateway and “RaspBee System” device in Pimatic are configured correctly and work. Below you can see that the message log provides info that raspbee and the Phoscon-Gateway are working in general.

Still trying to find the root cause for not finding the devices with “Discover Devices” I ask you if you can post an example config of your “RaspBeeMultiSensor” device here so that I can manually add this to my pimatic config just changing the IDs?

I have tried to understand the documentation on the “RaspBeeMultiSensor” device but there are several IDs named that are not further described. An example config (which I could not find anywhere online) would help me to figure out how to configure that manually.

Best and Cheers,
Arrow

23:11:56info [pimatic-raspbee]: API key valid
23:11:56info [pimatic-raspbee]: Software Version 2.5.77
23:11:56info [pimatic-raspbee]: API 1.16.0
23:11:56info [pimatic-raspbee]: Name Phoscon-GW
23:11:56info [pimatic-raspbee]: Connection establisedinfo [pimatic-raspbee]: config send
23:21:40info [pimatic-raspbee]: scan finished
23:21:14info [pimatic-raspbee]: Type > ZHAPressure
23:21:14info [pimatic-raspbee]: Model > lumi.weather
23:21:14info [pimatic-raspbee]: Manu > LUMI
23:21:14info [pimatic-raspbee]: Name > Pressure 13
23:21:14info [pimatic-raspbee]: UID > 00:15:8d:00:04:83:xx:xx-01-0403
23:21:14info [pimatic-raspbee]: Resource > sensors
23:21:14info [pimatic-raspbee]: ID > 13
23:21:14info [pimatic-raspbee]: new device paired!
23:21:14info [pimatic-raspbee]: Type > ZHAHumidity
23:21:14info [pimatic-raspbee]: Model > lumi.weather
23:21:14info [pimatic-raspbee]: Manu > LUMI
23:21:14info [pimatic-raspbee]: Name > Humidity 12
23:21:14info [pimatic-raspbee]: UID > 00:15:8d:00:04:83:xx:xx-01-0405
23:21:14info [pimatic-raspbee]: Resource > sensors
23:21:14info [pimatic-raspbee]: ID > 12
23:21:14info [pimatic-raspbee]: new device paired!
23:21:14info [pimatic-raspbee]: Type > ZHATemperature
23:21:14info [pimatic-raspbee]: Model > lumi.weather
23:21:14info [pimatic-raspbee]: Manu > LUMI
23:21:14info [pimatic-raspbee]: Name > Temperature 11
23:21:14info [pimatic-raspbee]: UID > 00:15:8d:00:04:83:xx:xxb-01-0402
23:21:14info [pimatic-raspbee]: Resource > sensors
23:21:14info [pimatic-raspbee]: ID > 11
23:21:14info [pimatic-raspbee]: new device paired!
23:20:35info [pimatic-raspbee]: Start new pairing mode for 60 seconds
23:12:04info [pimatic-raspbee]: Event receiver connected.
23:11:56info [pimatic-raspbee]: API key valid
23:11:56info [pimatic-raspbee]: Software Version 2.5.77
23:11:56info [pimatic-raspbee]: API 1.16.0
23:11:56info [pimatic-raspbee]: Name Phoscon-GW
23:11:56info [pimatic-raspbee]: Connection establised

Thrusty

@arrowx
Hello, did you previously set in the Phoscon app that a connection is possible?
You have to tap on the three lines in the upper left corner. Then on the left side on “Gateway” then on the bottom right on “Advanced” and then on “Connect App”.
Pimatic will then use “Discover…” to find the devices.

kosta

hi @ArrowX
the procedure is as follows:

first link the plugin to the api.
-> this looks good.
then either via the deconz gui or via the pimatic “rasbbee system device” start a discovery.
this step connects the device only to the deconz api at first.
-> you have started a scan by clicking the button according to the log.
then start a device scan via pimatic (in the device menu).
there the raspbee devices should be detected automatically and you can add them.

small explanation of the MultiDevice:

The device combines several virtual objects of the deconz api
Basic identifier is the UID/deviceID. (00158d000483xxxx without postfix -XXXXX)
The sensorIDs is only a loose collection of all IDs that belong to it. In your case 11/12/13.
The supportMap contains a loose collection of the features:
temperature/pressure/humidity

ArrowX

I have found a solution for my issue. The “Discover Devices” action was blocked by a faulty configuration of a completely different pluging (in my case pimatic-mqtt) that hindered the device discovery of raspbee. After disabeling the other plugin “Discover Devices” worked fine!