Bitte um Hilfe, bekomme die Funk Türklingel nicht zum Laufen.

---

Versuche die Türklingel von „Paget Trading Ltd.“ in mein Pimatic einzubinden. Homeduino ist soweit installiert und scheint zu laufen.
Die Debug-Ausgabe beim drücken der Taste ist auch sichtbar.

• switch25: { unitCode: 12, state: false }
• 14:40:18debug [pimatic-homeduino]: received: [ 380, 860, 11004 ] 100110011001100110011001100110010101010101010101101010010101010102
• 14:40:18debug [pimatic-homeduino]: data: “RF receive 860 380 11004 0 0 0 0 0 011001100110011001100110011001101010101010101010010101101010101012”

Habe es versucht als „HomeduinoRFButtonsDevice“ einzubinden, nur bekomme ich es nicht zum laufen. Als Empfänger kommt ein SRX882 und Sender STX882 über Arduino an einem RPI3 angeschlossen zum Einsatz.

{
  "buttons": [
    {
      "id": "Klingeln",
      "text": "klingel-eingang",
      "protocols": [
        {
          "name": "switch25",
          "options": {
            "unitCode": "12",
            "state": "false"
          }
        }
      ]
    }
  ],
  "id": "rf-klingel-eingang",
  "name": "RF-Klingel Eingang",
  "class": "HomeduinoRFButtonsDevice"
},

Als Kernel habe ich aktuell 4.9.41-v7+ und gpio Version: 2.44 auf dem RPI3 installiert.

Unter „make monitor“ bekomme ich einmalig beim drücken des Buttons „ACK“ angezeigt, danach passiert nichts mehr bis ich den RPI3 neu starte. Wo liegt nun der Wurm begraben?

@sanja9 i think klingel is a doorbell so it should be a PIR instead of a switch protocol.

Please press the button a couple of times and post the debug here. My doorbell was only detected after holding it for 2 seconds.

The debug output is always repeated.

• debug [pimatic-homeduino]: switch25: { unitCode: 12, state: false }
• 16:16:18debug [pimatic-homeduino]: received: [ 376, 864, 10996 ] 101001101001100110011010101001100101010101010101101010010101010102
• 16:16:18debug [pimatic-homeduino]: data: “RF receive 864 376 10996 0 0 0 0 0 010110010110011001100101010110011010101010101010010101101010101012”
• 16:16:18debug [pimatic-homeduino]: switch25: { unitCode: 12, state: false }
• 16:16:18debug [pimatic-homeduino]: received: [ 376, 864, 10996 ] 101001101001100110011010101001100101010101010101101010010101010102
• 16:16:18debug [pimatic-homeduino]: data: “RF receive 864 376 10996 0 0 0 0 0 010110010110011001100101010110011010101010101010010101101010101012”
• 16:16:18debug [pimatic-homeduino]: switch25: { unitCode: 12, state: false }
• 16:16:18debug [pimatic-homeduino]: received: [ 376, 864, 10996 ] 101001101001100110011010101001100101010101010101101010010101010102
• 16:16:18debug [pimatic-homeduino]: data: “RF receive 864 376 10996 0 0 0 0 0 010110010110011001100101010110011010101010101010010101101010101012”

@sanja9 this device is not a “plug and play” device for homeduino. This is why you dont get a pir as debug. You could try and make your own PIR which should be easy if you follow this guide; https://github.com/pimatic/pimatic-homeduino/issues/31

ok, thanks for the hint, i’ll try it.

I did it, now I can see pir2.

debug [pimatic-homeduino]: pir2: { unit: 4, id: 21, presence: true }

But I can not send an RF command to my doorbell. I can only see if the RF remote control is pressed. My goal is to send a command to doorbell via Pimatic. How should I proceed here?

@sanja9 well done, you have just created a protocol!

Ah ringing it… well to be honest, that is a good question which i cant answer.

I might have a suggestion. Are you able to “pair” a new doorbell button to your doorbell? If so, create a new button with the correct unit and id, put the bell on learning mode, and press the button!

@sanja9 said in Bitte um Hilfe, bekomme die Funk Türklingel nicht zum Laufen.:

false

I tried it, it does not work that way. How can I send the data from my remote control via Pimatic?

@sanja9 please post exactly which doorbell you have.