but, for flashing must i connect the ESP01 with a Arduino, in my case, with a UNO, or?
or must i connect the ESP with the Raspberry? or need i a FTDI FT232-Seriell-USB?
-
ESPEasy with Pimatic over MQTT
-
You need a FTDI cable (USB to serial)
Like my projects and help? Consider donating electroneum etnjwAKGPqF6omQWRmpp9u2BPyVDG9VuyRQjNJ1S8yfBdfR9qeUQ46kRy8KS2CNqbpNLRrsgmNW6F2TMzxmZgPrh6KctrkrYbm
-
ok, i havent it…
must buy one
-
And it must be a 3.3V version or switchable 5V/3.3V.
Or over TX/RX. But without logic level converter I would not go into it
Pimatic = Smart Home
-
You can use an arduino to flash the ESP, havent tested it with a UNO http://yaab-arduino.blogspot.nl/2015/12/flashing-esp8266-firmware-arduino.html
A nano can be used as well but the easiest wasy is an FTDI cableFollow my domotica project on http://maredana.nl
-
hello
what means this error from the arduino v1.6.7 ?
exit status 1
no matching function for call to ‘PubSubClient::PubSubClient(const char [1])’ -
Use 1.6.5
Pimatic = Smart Home
-
ok, thx…
1.6.5 seems ok, but Arduino dont upload the complete ino file.
I guess that’s at 90 percent circuit.
Blue LED stopps blinking.Arduino software shows
upload xxxx …
…i have a ESP01 Black Edition with 1MB.
-
What error do you get?
Like my projects and help? Consider donating electroneum etnjwAKGPqF6omQWRmpp9u2BPyVDG9VuyRQjNJ1S8yfBdfR9qeUQ46kRy8KS2CNqbpNLRrsgmNW6F2TMzxmZgPrh6KctrkrYbm
-
@ noxx
try that: http://www.esp8266.nu/index.php/Tutorial_ESPEasy_Firmware_Upload
-
i play a little bit with espeasy, but i get now values…
{ "class": "MqttSimpleSensor", "id": "espeasy1", "name": "ESP01_01", "mqtturl": "mqtt://192.168.1.81", "attributes": [ { "name": "uptime", "topic": "/espeasy1/system/esp01uptime", "type": "number", "unit": "minute", "acronym": "Uptime" }, { "name": "freeram", "topic": "/espeasy1/system/esp01ram", "type": "number", "unit": "B", "acronym": "FreeRAM" } ] }
ESPeasy:
http://www.bilder-upload.eu/show.php?file=8ecdc2-1455990079.png -
@noxx
R80 provides WiFi RSSI.{ "name": "wifi-rssi", "topic": "wemosd1r2/system/wifi-rssi", "type": "number", "unit": "dB", "acronym": "WiFi-RSSI" }
Pimatic = Smart Home
-
i use R78
i dont know whats wrong with my config
http://www.bilder-upload.eu/show.php?file=e85b1d-1456001509.png
http://www.bilder-upload.eu/show.php?file=f87193-1456001520.png
http://www.bilder-upload.eu/show.php?file=87c54b-1456001656.png
"class": "MqttSimpleSensor", "id": "esp01", "name": "ESP-01", "mqtturl": "mqtt://192.168.1.81", "attributes": [ { "name": "uptime", "topic": "/esp01/system/uptime", "type": "number", "unit": "minute", "acronym": "Uptime" }, { "name": "freeram", "topic": "/esp01/system/freeram", "type": "number", "unit": "B", "acronym": "FreeRAM" } ] }
-
With this module https://github.com/wutu/pimatic-mqtt is possible to use other options.
Pimatic = Smart Home
-
@noxx check whether the template is filled. Tools > Advanced.
Pimatic = Smart Home
-
@noxx This seems ok . If you set Serial log level to 4. 'll see if it emits data to broker.
Pimatic = Smart Home
-
@wutu said:
@noxx This seems ok . If you set Serial log level to 4. 'll see if it emits data to broker.
hope this help
218929 : MQTT : Connection lost
221458 : MQTT : Failed to connected to broker
223583 : MQTT : Failed to connected to broker
224174 : SYS : 3.00
224177 : SYS : 26184.00
224178 : HTTP : Delay 1000 ms
248930 : WD : Uptime 4 ConnectFailures 14 FreeMem 26328
248930 : MQTT : Connection lost
251531 : MQTT : Failed to connected to broker
253681 : MQTT : Failed to connected to broker -
@noxx Runs the broker? Mosquitto you installed ? If so, try:
sudo /etc/init.d/mosquitto status
Pimatic = Smart Home
-
@wutu said:
@noxx Runs the broker? Mosquitto you installed ? If so, try:
sudo /etc/init.d/mosquitto status
pi@raspberrypi:~ $ sudo /etc/init.d/mosquitto status
- mosquitto.service - LSB: mosquitto MQTT v3.1 message broker
Loaded: loaded (/etc/init.d/mosquitto)
Active: active (running) since Sa 2016-02-20 22:46:01 CET; 4min 41s ago
CGroup: /system.slice/mosquitto.service
`-20785 /usr/sbin/mosquitto -c /etc/mosquitto/mosquitto.conf
Feb 20 22:46:01 raspberrypi mosquitto[20780]: Starting network daemon:: mosq…
Feb 20 22:46:01 raspberrypi systemd[1]: Started LSB: mosquitto MQTT v3.1 mes…
Hint: Some lines were ellipsized, use -l to show in full.
pi@raspberrypi:~ $what i dont unterstand. how recognizes espeasy the pimatic system?
esp is connected via wlan
pimatic via lan
both with my router
must i add the ip adress of the pimatic system in espeasy? if yes, where? - mosquitto.service - LSB: mosquitto MQTT v3.1 message broker