@mwittig in the example on http://pimatic.org/plugins/pimatic-homeduino/ is no debug entry.
Maybe someone should add some info on this page.
-
Radio remote control commands read ? - Rohrmotor24
-
@Flop2006: Yes, you are right. The web page needs to be updated. Note, however, my previous post: debug is set true by default. So, you don’t need to change the plugin config. See also https://github.com/pimatic/pimatic-homeduino/blob/master/homeduino-config-schema.coffee for reference
All you need to do is enable the Debug Log level in Pimatic as I pointed earlier. See the screenshot posted by @leader21 - It is the drop down box in the top-left corner.
"It always takes longer than you expect, even when you take into account Hofstadter's Law.", Hofstadter's Law
-
Ok. Ich schreib jetzt gleich mal auf Deutsch. Geht schneller
Also der Debugmodus ist an. Ich hab auch die Tipps soweit nachvollzogen doch leider ohne Erfolg. Ich sehe nicht mal die Befehle von der Intertechno Fernbedinung. Wo könnte noch der Fehler sein?
Gruß Ronny -
Hast du überhaupt einen receiver angeschlossen?
Könntest du davon mal ein Bild posten?pimatic rocks!!!
-
wenn ja - welchen? da gibts durchaus qualitative unterschiede!
edit - habe gerade in deiner wirebox gesehen dass du den “billig” receiver nutzt.
verwende den 3400RF bzw. RXB6 dann gibts auch weniger Probleme mit dem Empfang.Hab das mal kurz hier zusammengefasst http://forum.pimatic.org/topic/487/hardware-tip-433-mhz-receiver-for-pimatic
pimatic v0.9 has been released!
Support Pimatic and get some free stickers
Like us on Facebookmake it so !
-
Hallo. Ja genau den Billigen
Ok werd mal schauen das ich den anderen im Netz finde und dann austausche.
Danke erst mal für die Hilfe.
Gruß Ronny -
pimatic v0.9 has been released!
Support Pimatic and get some free stickers
Like us on Facebookmake it so !
-
Danke… und schon bestellt.
Hab was gefunden wo ein anderes Projekt auch mit den Motoren von Rohrmotor24 arbeiten. Denke mal da sollte ein weg drin sein das das dann auch geht. https://everhome.de/link text
-
You can use the rohrmotor24 protocol as shutter1 now with homeduino. For that you will have to update homeduino at your nano.
pimatic v0.9 has been released!
Support Pimatic and get some free stickers
Like us on Facebookmake it so !
-
Hello i am gerrit from holland and i am try to use pimatic with rasp pi and arduino nano and sending /tranceiving set RXB6 and KXD10036.
I works fine with KAKU but i also want to use it for my shutters.
I have 3 rohrmotor24 for my shutters that i close with 5 canals remote.
Iam not so good with the computer so i ask if you can help me.
I can receive some data from the remote but i dont now how to use it as a device. I would like it to use as UP STOP DOWN.Log messages
DebugAll
USING THE STOP BUTTON.
Showing 2 of 0 Messages
2015-05-08 07:40:41debug [pimatic-homeduino]: received: [ 348, 712, 1492, 4744, 6616 ] 3201010110010101100101100101010101100101101010100101011001010110100110011001100114
07:40:41debug [pimatic-homeduino]: data: “RF receive 4744 1492 348 712 6616 0 0 0 0123232332232323322323322323232323322323323232322323233223232332322332233223322334”BUTTON UP
Log messages
DebugAll
Showing 4 of 0 Messages
2015-05-08 07:56:50debug [pimatic-homeduino]: received: [ 352, 712, 1488, 4748, 6976 ] 3201010110010101100101100101010101100101101010100101011001010110100101011010101004
07:56:50debug [pimatic-homeduino]: data: "RF receive 4748 1488 352 712 6976 0 0 0 0123232332232323322323322323232323322323323232322323233223232332322323233232323224"
07:56:50debug [pimatic-homeduino]: received: [ 352, 712, 1476, 4760, 6616 ] 3201010110010101100101100101010101100101101010100101011001010110100101011001010114
07:56:50debug [pimatic-homeduino]: data: "RF receive 4760 1476 352 712 6616 0 0 0 0123232332232323322323322323232323322323323232322323233223232332322323233223232334
Thanks. -
@ghv
hello gerrit! first of all welcome to Pimatic and good choice to use RXB6
@willy did some great codework hereDid you update your nano with the latest homeduino sketch? If not please first try that and see if you can receive any id at the debug messages.
If you already updated and still have no clear debug, guess we (@willy ) need to develop a new shutter device.
cheers
chrispimatic v0.9 has been released!
Support Pimatic and get some free stickers
Like us on Facebookmake it so !
-
I need the debug from all channels:
Channel1 up, down, stop
Channel2 up, down, stop
ect.Please post this in a new thread in “RF Protocols”
-
Dear Willy and Chris
Thanks for your reaction.
I have update everything but i see now also not an id number.
I will give you soon all the data from the channels 1 to 5.Already thanks, gerrit.
-
Hallo.
und gleich wieder auf Deutsch. Geht schneller. Hoffe das ist kein Problem.
bin zurück aus dem Urlaub und die neuen Bauteile sind auch da. Werd das mal entsprechend umbauen und melde mich dann obs klappt.
Aber wie ich sehen hat sich ja hier schon was getan. Das Protokoll ist schon im pimatic verbaut. Ich bin begeistert.Gruß Ronny
-
So Modul getauscht und das Auslesen Funktioniert.
Jetzt habe ich mal geschaut und das Device entsprechend eines anderen Beitrages eingerichtet. Nur weiss ich jetzt nicht wie ich meine ID aus den Ganzen Zahlen zusammenbaue. Wäre für Hilfe Dankbar. -
@rowoy
Da rohrmotor24 noch nicht in den offiziellen Quellen drin ist, versuch mal das:shutter4.js downloaden
Stop pimatic
kopiere “shutter4.js” nach “/home/pi/pimatic-app/node_modules/pimatic-homeduino/node_modules/homeduino/node_modules/rfcontroljs/lib/protocols”
füge , ‘shutter4’ am Ende der Zeile 6 von “/home/pi/pimatic-app/node_modules/pimatic-homeduino/node_modules/homeduino/node_modules/rfcontroljs/lib/controller.js” ein:
Zuvor (die Namen können anders aussehen!):
....... 'shutter2', 'shutter3''];
Nach dem Einfügen:
....... 'shutter2', 'shutter3', 'shutter4'];
Start pimatic
Wenn du eine Taste auf deiner original Fernbedienung drückst, solltest du in etwa sowas sehen:
[pimatic-homeduino] debug: shutter4: { id: 35918788, channel: 1, command: up, all: false }
Und dann fügst du in deinem Device die angezeigte id und Kanal ein.
-
Hallo Willy
Danke für den Tipp. Hab das jetzt endlich mal ausprobiert und was soll ich sagen. SUPER… es geht. Vielen Dank.
Gruß Ronny
-
Hallo Willy
versuche gerade eine Rule zu erstellen. Wie genau spreche ich den Shutter jetzt an?
Gruß Ronny
-
Hi,
hast du Buttons für die Befehle verwendet? Dann in etwa so:
IF it is 21:00 THEN press rolladen1-ab
Dann wird um 21 Uhr der Button für rolladen1-ab gedrückt.
-
Hallo .
Danke für den Hinweis. Hab das jetzt mal versucht. Device schauen so aus. Im Moment hab ich zwei Rollos.{ "id": "rolladenF", "name": "Rolladen Fenster", "class": "HomeduinoRFButtonsDevice", "buttons": [ { "id": "roll1", "text": "Rauf", "protocols": [ { "name": "shutter4", "options": { "id": 6559260, "channel": 2, "command": "up" } } ] }, { "id": "roll2", "text": "Stop", "protocols": [ { "name": "shutter4", "options": { "id": 6559260, "channel": 2, "command": "stop" } } ] }, { "id": "roll3", "text": "Runter", "protocols": [ { "name": "shutter4", "options": { "id": 6559260, "channel": 2, "command": "down" } } ] } ] },
Gruß Ronny